AFMG Network Forum
AFMG Network Forum Index -> EASE 4 -> modeling in Ease
Post new topic  Reply to topic View previous topic :: View next topic 
modeling in Ease
PostPosted: Mon Dec 21, 2015 4:49 pm Reply with quote
mohammad_hed
Member
 
Joined: 27 Sep 2015
Posts: 8




Hi
I have a problem in modeling structure.I want to creat a cupola but It's Internal volume doesn't apear.
In the following, I sent images from model of the project.
http://s6.picofile.com/file/8228944100/1.png
http://s6.picofile.com/file/8228945184/2.png
Please guide me

[/list]
View user's profile Send private message
PostPosted: Tue Dec 22, 2015 2:42 pm Reply with quote
AFMG Pedro Lima
Forum Moderator
 
Joined: 05 Jun 2010
Posts: 266
Location: Germany




Hello,

Make sure the Faces of your cupola are not inverted (Yellow side must face towards the room inside). Also check if the Two-Fold Face box is unchecked in the Face properties.

Also, you must remove the bottom Face of it and make the contour so that the cupola volume is part of the room volume.

BTW, these Faces in the middle of the room were supposed to be the Audience? If yes, insert Audience Areas instead of Faces. Smile

HTH,
Pedro
View user's profile Send private message
PostPosted: Wed Dec 23, 2015 11:54 am Reply with quote
thomas
Member
 
Joined: 16 Mar 2011
Posts: 73




Hi,
make sure the lowest vertices of your cupola are part of the plane ceiling.
I think, you have to erase the plane ceiling and make it new, including the lowest vertices of the cupola.

BTW, if these Faces in the middle of the room were supposed to be the Audience, give them the properties (alfa, scattering coeff) of the audience. Sometimes it is even better to make a box for the audience (ca. 0.6 m high for sitting, ca. 0,8 m for upright standing and I'd suppose ca. 0,3 m for kneeling people), all faces with the properties of the audience. The EASE-audience-area floats above this face/box.

kind regards
thomas
View user's profile Send private message
PostPosted: Wed Dec 23, 2015 12:58 pm Reply with quote
mohammad_hed
Member
 
Joined: 27 Sep 2015
Posts: 8




Dear Pedro,
I unchecked the two-fold box of the cupola face but when I wanted to check data, I encountered with Hole error.
View user's profile Send private message
PostPosted: Wed Dec 23, 2015 1:03 pm Reply with quote
mohammad_hed
Member
 
Joined: 27 Sep 2015
Posts: 8




Dear Thomas,
The lowest vertices of my cupola are equal to the ceiling height.
View user's profile Send private message
PostPosted: Wed Dec 23, 2015 2:07 pm Reply with quote
AFMG Pedro Lima
Forum Moderator
 
Joined: 05 Jun 2010
Posts: 266
Location: Germany




Hi Mohammad,

Please check the "Finding and Fixing Holes" section of the EASE Tutorial (http://www.afmg-support.eu/SoftwareDownloadBase/EASE/EASE_4.3_Tutorial_English.pdf) for more info on how to find and close holes.

EASE will always expect the same things from you. These are exposed in that section (I believe you already read the tutorial a few times? Wink). What Thomas mentioned above about the vertices is one of the drawing errors you might find. All neighbor Faces must share the same vertices. And since you cannot open a hole to insert your cupola, you will have to split the ceiling Face in order to surround your cupola base.

HTH,
Pedro
View user's profile Send private message
AFMG Network Forum Index -> EASE 4
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT  
Page 1 of 1  

  
  
 Post new topic  Reply to topic  


Powered by phpBB © 2001-2003 phpBB Group
Theme created by Vjacheslav Trushkin
Variation by CodeWeavers and AFMG