 Posted: Sun Jun 05, 2011 2:48 pm |
 |
|
| jonessy |
| Member |
|
| |
| Joined: 22 Dec 2005 |
| Posts: 19 |
| Location: Israel |
|
|
|
|
|
| Hi All,
In my model, the RT ranges from 12 secs (at LF) to 1.9 secs (at HF).
When I run AURA, it calculates the response only up to ~ 300ms...
Even when I set the 'length' parameter manually to about 12000 ms, it still doesn't calculate the entire response.
How can this be fixed?
Kind regards,
Jon |
|
|
_________________
--Jonathan |
|
|
|
| Posted: Sun Jun 05, 2011 6:52 pm |
|
|
| AFMG Pedro Lima |
| Forum Moderator |
|
| |
| Joined: 05 Jun 2010 |
| Posts: 269 |
| Location: Germany |
|
|
|
|
|
| Hello Jonessy,
Would it be possible for you to send me the Project? Please, Pack it via EASE Main window > File menu > Pack Project, before sending. You can send to Pedro.Lima@AFMG.eu
Best Regards,
Pedro |
|
|
|
|
| Posted: Sun Jun 05, 2011 7:09 pm |
|
|
| jonessy |
| Member |
|
| |
| Joined: 22 Dec 2005 |
| Posts: 19 |
| Location: Israel |
|
|
|
|
|
|
|
_________________
--Jonathan |
|
|
|
| Posted: Sun Jun 05, 2011 8:15 pm |
|
|
| AFMG Pedro Lima |
| Forum Moderator |
|
| |
| Joined: 05 Jun 2010 |
| Posts: 269 |
| Location: Germany |
|
|
|
|
|
| Jonessy,
While our development team give this problem a deeper investigation, you can try to export your model as DXF and then reimport it to EASE again. This should be enough to solve your problem and will allow you to run AURA calculations with no problem again.
Also notice that, on EASE EYES, it is not possible to see all the faces. Specially the ceiling ones. It should be related to your problem.
Please return to me if you have further questions,
Best Regards, |
|
|
|
|
| Posted: Sun Jun 05, 2011 8:20 pm |
|
|
| AFMG Pedro Lima |
| Forum Moderator |
|
| |
| Joined: 05 Jun 2010 |
| Posts: 269 |
| Location: Germany |
|
|
|
|
|
| BTW,
To export to DXF:
- Open your Project on EASE;
- Open EASE IMEX from the File menu > Import / Export;
- Next, from the Tools pulldown menu, choose Export DXF;
To import to DXF:
- Perform the same procedure but this time choose Import DXF/SKP
HTH |
|
|
|
|
| Posted: Mon Jun 06, 2011 7:24 pm |
|
|
| jonessy |
| Member |
|
| |
| Joined: 22 Dec 2005 |
| Posts: 19 |
| Location: Israel |
|
|
|
|
|
| Thanks for the workaround...
Seems like it gets the job done.
Cheers,
Jon. |
|
|
_________________
--Jonathan |
|
|
|
| AFMG Network Forum Index -> EASE 4 |
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
All times are GMT
Page 1 of 1
|
|
|
|
|
AFMG Network Forum
