 Posted: Wed Sep 30, 2009 8:07 pm |
 |
|
| Justin |
| Member |
|
| |
| Joined: 30 Sep 2009 |
| Posts: 4 |
|
|
|
|
|
|
| I'm trying to model a three story atrium that is about 180,000 ft^3. The RT I'm getting is around 1 second, despite most of my surface area being reflective (glass, tile, and gyp). I find this result hard to believe.
Also, when I try and ray trace this space it gives me an error message saying, "No Valid impacts for local decay". I would guess that these might be interconnected problems, but not sure. Any ideas? |
|
|
|
|
| Posted: Wed Sep 30, 2009 8:09 pm |
|
|
| Jim Mobley |
| Member |
|
| |
| Joined: 27 Jul 2005 |
| Posts: 134 |
| Location: Foothill Ranch, California, USA |
|
|
|
|
|
| Hi Justin,
Is the model closed? In Edit Project, Edit > Project Data > Data tab, uncheck Room Open. |
|
|
_________________
Best regards,
Jim Mobley
Sr. Application Engineer
Renkus-Heinz, Inc.
19201 Cook St.
Foothill Ranch, CA 92610 USA
TEL: +1-949-588-9997
FAX: +1-949-588-9514
www.renkus-heinz.com
mailto:jim@renkus-heinz.com |
|
|
|
| Posted: Wed Sep 30, 2009 8:18 pm |
|
|
| Justin |
| Member |
|
| |
| Joined: 30 Sep 2009 |
| Posts: 4 |
|
|
|
|
|
|
| Yes, the model is closed and all the faces are facing the correct way. |
|
|
|
|
| Posted: Wed Sep 30, 2009 8:54 pm |
|
|
| Jim Mobley |
| Member |
|
| |
| Joined: 27 Jul 2005 |
| Posts: 134 |
| Location: Foothill Ranch, California, USA |
|
|
|
|
|
| Hi Justin,
We could go back and forth for a couple of days, but if you could, just pack the project and send it to me at the address below.
Thanks. |
|
|
_________________
Best regards,
Jim Mobley
Sr. Application Engineer
Renkus-Heinz, Inc.
19201 Cook St.
Foothill Ranch, CA 92610 USA
TEL: +1-949-588-9997
FAX: +1-949-588-9514
www.renkus-heinz.com
mailto:jim@renkus-heinz.com |
|
|
|
| Posted: Thu Nov 12, 2009 5:12 pm |
|
|
| lchow |
| Member |
|
| |
| Joined: 19 Aug 2009 |
| Posts: 2 |
|
|
|
|
|
|
| Jim, I am having some similar issues amongst other things.
Would it be ok for me to send you my project file for your review as well?
thanks. |
|
|
|
|
| Posted: Thu Nov 12, 2009 5:36 pm |
|
|
| Jim Mobley |
| Member |
|
| |
| Joined: 27 Jul 2005 |
| Posts: 134 |
| Location: Foothill Ranch, California, USA |
|
|
|
|
|
| Yes of course. We at Renkus-Heinz should be your first EASE, EASERA and SysTune support contact. |
|
|
_________________
Best regards,
Jim Mobley
Sr. Application Engineer
Renkus-Heinz, Inc.
19201 Cook St.
Foothill Ranch, CA 92610 USA
TEL: +1-949-588-9997
FAX: +1-949-588-9514
www.renkus-heinz.com
mailto:jim@renkus-heinz.com |
|
|
|
| AFMG Network Forum Index -> EASE 4 |
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
All times are GMT
Page 1 of 1
|
|
|
|
|
AFMG Network Forum
