AFMG Network Forum
AFMG Network Forum Index -> AFMG EASERA -> No Hardware Reference File with Phantom Power !!!
Post new topic  Reply to topic View previous topic :: View next topic 
No Hardware Reference File with Phantom Power !!!
PostPosted: Mon Oct 31, 2005 8:31 am Reply with quote
Tobi @ Fohhn Audio AG
Member
 
Joined: 25 Oct 2005
Posts: 13




Hi everyone,
this is a warning for everybody who uses the FireBox: Be sure you have switched off the 48V Phantom power befor you loop the output back to the MIC input to make a Referencefile or a Volume Calibration.
Otherwise you damage the output of the FireBox !!!
I think Presonus should eliminate this problem soon, because the output of such a Interface shold normally be resistant against Phantom Power ... or EASERA has to include a warning in the calibration procedure
Greetings
Tobi
View user's profile Send private message Visit poster's website
PostPosted: Mon Oct 31, 2005 10:32 am Reply with quote
Stefan
Member
 
Joined: 19 Apr 2005
Posts: 167
Location: Berlin, Germany




Dear Tobi,

we have three FireBox models here. We just checked your finding, but we could not reproduce it. Neither of the three was damaged when measuring with the output looped back to the microphone input with phantom power on.

Please provide more details. Thank you!

Stefan
View user's profile Send private message Send e-mail Visit poster's website
PostPosted: Mon Oct 31, 2005 1:40 pm Reply with quote
Tobi @ Fohhn Audio AG
Member
 
Joined: 25 Oct 2005
Posts: 13




Hi Stefan,
the first thing I have done after the installation of my brand new FireBox, was muting the MIC 1 & 2 channel in the FireboxMixer. After that I wanted to measure a frequency response of a loudspeaker. I checked the soundcard with a poweramp and my speaker, and started a test signal. Everything fine. Afterthat I needed the ref. file of the FireBox, I turned the Mic gain and the Main Output down to disable clipping. I looped the main output (firebox) back to input MIC1. The 48V button was on. In the same moment I plugged in, all lights of the FireBox turned down, and EASERA crashed with a few error messages. After that the main output was damaged, no more sound came out.
I could not belive, so I have done the same with the Line Output 2. Now it is also damaged... very strange...
View user's profile Send private message Visit poster's website
PostPosted: Mon Oct 31, 2005 1:54 pm Reply with quote
Stefan
Member
 
Joined: 19 Apr 2005
Posts: 167
Location: Berlin, Germany




Hi Tobi,

we have forwarded this case to PreSonus and hope for an answer soon. Unfortunately we cannot reproduce it, and also we are not responsible for the HW support so you may want to turn to your PreSonus dealer.

We will post any news here as soon as we get them.

Stefan
View user's profile Send private message Send e-mail Visit poster's website
PostPosted: Mon Oct 31, 2005 4:54 pm Reply with quote
Bruce
Member
 
Joined: 19 Apr 2005
Posts: 459
Location: Minneapolis, MN, USA




Tobi @ Fohhn Audio AG wrote:
I looped the main output (firebox) back to input MIC1. The 48V button was on. In the same moment I plugged in, all lights of the FireBox turned down, and EASERA crashed with a few error messages. After that the main output was damaged, no more sound came out.


Hi Tobi,

Sorry to hear this. I have done this many times without a problem with my FireBox, so I am wondering what the difference is. Which connection did you make last? The XLR to the Mic input, or the 1/4" to the output. I have always had the output connected first, then plugged in the XLR for the input.

_________________
Best Regards,
Bruce C. Olson
View user's profile Send private message Send e-mail Visit poster's website
PostPosted: Tue Nov 08, 2005 2:16 pm Reply with quote
Stefan
Member
 
Joined: 19 Apr 2005
Posts: 167
Location: Berlin, Germany




This is the response we received from PreSonus regarding the above issue:

"We had seen this on isolated units some time ago and had attributed it to a
particular brand of opamp. It's been several months if not over a year
since an ECO was issued to change brands and I don't know of any recurrence
of this problem. All the units you receive should have the acceptable brand
of opamp and I do not expect problems."
View user's profile Send private message Send e-mail Visit poster's website
AFMG Network Forum Index -> AFMG EASERA
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT  
Page 1 of 1  

  
  
 Post new topic  Reply to topic  


Powered by phpBB © 2001-2003 phpBB Group
Theme created by Vjacheslav Trushkin
Variation by CodeWeavers and AFMG